Our customers made these suggestions for improving Heatmiser. Suggestions for improving Heatmiser.
We reserve the right to change / cancel or delay any planned feature listed here.
With this in mind, you should NOT purchase a product based on any future feature listed here, including those marked as planned.
Comments asking for release dates will NOT be approved for inclusion here as we don’t promise anything before we can deliver it.
With this in mind, you should NOT purchase a product based on any future feature listed here, including those marked as planned.
Comments asking for release dates will NOT be approved for inclusion here as we don’t promise anything before we can deliver it.
Homekit-capable hard-wired switch - ideally two-way and intermediate.
It would open up so many possibilities to have a switch which could be hard-wired into circuits to give Homekit control, rather than just a plug-in one.
If it ...
Under consideration
Plugged in electrical thermostat
Please try to manufacture a new electrical thermostat that can be plugged in to already existing electrical socket. This way we avoid the cost of batteries and the ...
Not planned
Target temperature bands for time of use electrical tariffs when using domestic Heat Pumps
Target temperature bands will allow the system to heat to the maximum target temperature when electrical tariffs are cheap and when electrical tariffs are high only ...
Not planned
Access to more detailed information for installers
The hub API provides far more information than is present in the standard user app, for both thermostats/devices and the hub. Could a "pro/installer" mode be ...
Not planned
Calibration of sensor from the app
Suggestion for a future release is to be able to calibrate the temp sensor from the app. Currently this is done from the keypad, but when it’s at the back of a ...
Not planned
iPhone App Update
On my Apple iPhone app, when a room thermostat is requesting the boiler to fire up, I see a flame symbol to the right of the zone that is heating. I do not see that ...
Not planned
Standby returning to it last setting
When standby returns to non standby mode it returns to the programmed time/temperature settings rather than its last setting which may be an overiden temperature. ...
Not planned
Add a MAXIMUM temperature setting.
In an office situation using the up/down setting to limit the maximum temperature is OK during standard working hours. However, out of hours (evenings & weekends) ...
Not planned
Add history to Timers and RF Switches (to also allow mesh history)
At the moment, for Neostat HW, and RF switch units there is no history available. Which also makes it impossible to know whether units are consistently online, ...
Planned
Conrad connect IOT portal support
https://conradconnect.com/en
Conrad Connect allows you to execute complex home automation routines that
would normally require using separate ...
Not planned
RF Switch online status indication
I am currently sorting a problem where two Neo stat HW’s and an RF Switch located very close to each other fail to mesh
I cannot tell when the RF Switch is connected ...
Not planned
neoStat-hw White V2 - Timer should allow more time on/off periods to be set
I am going to use a neoStat-hw V2 to control a Hot Water circulating pump. However on my manual control I have 5 on off periods set. I cannot relate this to the Neo ...
Not planned
Allow HomeKit to trigger Heatmiser recipes
I'd like to be able to trigger specific recipes with HomeKit automation
Done
Update history graph accurate
Dear,
could you improve the abscissa scale of the graph in question?
Three hours is a long time to properly analyze the temperature trend ...
You could also ...
Not planned
Sunset tracker CLOSED FOR NEW COMMENTS
Switching schedule that automatically tracks sunset at your location to operate outside lights. Could be ‘dusk to dawn’ or on for a selected period.
Done
Store Recipes on Hub
Please can I request that recipes are stored on the hub rather than individual apps. I have the app on my work laptop, personal laptop, ipad and Android phone. As the ...
Done
Neo app language choice
Add option to choose the (original) English language in the app when installed on a foreign (android) phone. The Dutch translation is buggy to say the least (part ...
Done
Simple config page for neoHub
Can we have a simple ip based web page to do config of the neoHub, in particular to choose which wi-fi network it picks.
Having bought a house with some complicated ...
Not planned
A replacement for SmartStat please!
SmartStat was great to allow thermostats around the house to be hosted on an existing home wifi network. Having invested in a comprehensive mesh wifi network, it is ...
Done
Sunset time option for switch on / off
Can you update the app to reflect sunset times so lights on and off timings can automatically adjust based on seasons
Done
How do I find out about new updates?
Hi, would it be possible to have an update page or blog page for firmware updates (or a changelog) so users can see what's new (or imminent). At present it seems like ...
Done
Improve Neoair thermostat battery warning level in Neo App
Currently, the Neo App will give a low battery level warning for wireless thermostats.
However, the batteries fail to be powerful enough before this warning ...
Done
Room Set Temperature
We have a NeoStat V2 which is very good but it will only allow me to adjust the room set temperature in 1c increments whilst the temperature differential can be ...
Done
Option to remove frost protection on "AWAY" mode - Heatmiser NEO
We go away for three weeks in February. We set "away". The temperature inside the house goes beneath frost protection point and the heating comes on. There is no ...
Done
Fused Switched Spur version for Towel Rail Control
Version of the Neostat-e v2 that can be used as a fused spur on a ring main to give timed control of an electric radiator.
Not planned
Heat sensor to be put in holder
Hi, I have a couple of Heatmiser heat sensors, however when I have to change the battery I have to peel off double sided tape, which is not practical. Could a holder ...
Not planned
NeoApp room/zone tiles in Hold screen to follow custom arrangement set in home screen
At present when the room/zone Tile layout has been custom re-arranged on the home screen with custom positioning, the Hold screen does not mirror the Home screen ...
Done
Enable room tiles in new grid display to be re-ordered
The new grid display for a summary of all the room stats is really good and thank you for implementing, but the order of the tiles for each room is fixed. For folks ...
Done
Lamp Post
I use the Neo Plug to control my Lamp Post outside. The cable runs from the end of my drive and essentially just arrives into my house into a plug which I plug into ...
Done
Add "hold cancel" to IFTTT
The option to cancel "hold" on IFTTT would give additional functionality to routines.
For example, if door open then hold heating at 10 degrees, if door dosed then ...
Done
Slave neoHub mini off neoHub
Enable neoHub mini to be slaved off of an existing neoHub so that its stats are seen as belonging to the neoHub. Effectively, the mini would just join the mesh of the ...
Not planned
Guest user specific zone control with limit on degrees plus or minus from set point.
Currently, guest users can be given limited access. It would be useful for admin to have ability for guest users to be limited to specific zones and zone with timers ...
Under consideration
Display mode data on Home page.
On the Home page, it would be most useful for the current mode, and associated data, to be displayed, along with the extant data. Doesn't need to take much room, or ...
Under consideration
SIMPLE, Really Large Display Characters (etc.) for Poorly Sighted People
This is a suggesion for a Programmable Thermostat as a simple, single channel CH Controller suitable for use by someone who has limited sight and NEEDS an ...
Not planned
Temp Differential change to 0.3
Being able to change the temp differential to 0.3 rather than 0.5
Not planned
IFTTT get current set temp & set a specific temp as an action
As part of integraton with Smartthings, I can put my Neo Air stats into standby when someone opens a window in the room. However, when the window is closed, I can't ...
Not planned
Add USB 'C' charging socket to Heatmiser neoAir v3 Wireless Smart Thermostat
Could you engineer a USB type C socket into your Heatmiser neoAir v3 Wireless Smart Thermostat to allow it to be charged or powered from a Standard USB 5V power ...
Not planned
Cool-down (the opposite of Pre-heating) could help save £££
The excellent pre-heating function means that zones are up to temperature by the scheduled time. This could work in reverse at the end of a scheduled heated period. ...
Under consideration
History search downloads should atart at the beginning of the day and end with the last
This may seem pedantic, but it is annoying...
When I download history files from date A to date B
I don't get the 00:00:00 entries for day A,and
I get just the ...
Under consideration
Use LocationServices to display nearest home when opening app
If the user has multiple homes set-up in the app then often the app is displaying the wrong one and the user has to tap the house icon and switch home.
It would ...
Under consideration
Home page displaying room temperature and controls
I have a rental boat and want to leave the thermostat page on all the time for my guests to be able to adjust and view. Currently there is a 5 minute timeout, after ...
Not planned
Add zones's away/frost protection set temp as comfort level temperature
I use a common heating profile used to control two zones; an underfloor zone and a radiator zone. Which is very convenient.
Each zone permits setting an "away" or ...
Not planned
Minimum on/off time for neo plug using manual or override option
Currently, there is a minimum time of 30 minutes for which it is possible to command a neoplug to 'on' using the manual or overrride function. Ideally, I would like ...
Under consideration
Win Desktop App - Enable Smart Control Features
Can we get enhanced history on the Win desktop app? Also a way of adjusting the temperature scale as few people have an inside temperature range of 5c to 35c. Thank ...
Not planned
Heating Boost activated by IFTTT battery PIR sensor
We use convectors for heating. we suggest an applet whereby Having the heating on a standby setting with a set back temperature which could be boosted to comfort ...
Not planned
Increase up/down limit range from 10 to 15 degrees
Our public use hall has long periods without any heating as the hall is not in use, at these times the temperature in the hall during the winter can drop close to ...
Suggested by:
Philip Bailey, East Harlsey Village Hall
(21 Jan, '22)
•
Upvoted: 21 Jan, '22
•
Comments: 0
Not planned
Daylight saving on Neostat without neohub
I would like to be able to switch automatically from summer to winter time without connecting a neohub.
Under consideration
Support for low temperature chilled ceiling solution
Please add a mode provides heating (Floor Heating) or cooling (Ceiling Cooling). More about the system: https://www.rehau.com/uk-en/rehau-chilled-ceiling-systems
Under consideration
Timer off recipe
Hi,
Any chance in the future you might create a 'timer off' recipe action that you can select a hold/override function for your Neo timers (hot water programmers). ...
Under consideration
Alert for low battery at configurable %age
Currently, I am getting alerts to tell me that my thermostat is 'low battery' at 20/25% (I dont recall which). However, given the batteries last well over a year, its ...
Not planned