Aggregated graph for all zones.
Related to https://feedback.heatmiser.com/suggestions/62176/boiler-burn-time-reportinggraph-neohub-gen-2 which suggests it is possible to see the aggregated total (how long heat was called for across all zones). However, Dan confirmed this is only at individual zones.
Could we have an aggregated view which shows when the first zone calls for heat, up to the last zone asking for heat to stop?
It would also be useful to see the number of zones calling for heat.
Comments: 15
-
08 Nov, '19
James MergedI have had the benefit of using a Heatmiser Neostat for over 12 months now, in what is my attempt to achieve a passive house self build.
My primary observation is that the underfloor heating system, installed throughout the house in various zones, when in use with the Neostat, operates to heat the house (which is relatively quickly) and then turns off for a far longer period. This results in the floor not remaining warm and therefore, not benefiting from the heating of the thermal mass concre -
08 Nov, '19
Martin Admin Merged"Timer measuring heating being on for each zone and all zones" (suggested by James on 2019-11-08), including upvotes (1) and comments (0), was merged into this suggestion.
-
08 Feb, '21
Darren MergedThis is marked as Done and I see that totals are available per zone/stat, but it'd be great to see aggregated totals - i.e. how long heat was called for across all zones per day.
1 -
06 Nov, '21
ric martin Mergedwhere can this information be seen?
1 -
07 Feb, '22
Paul MergedHow do you find this out? I can an individual stat/zone (https://faq.heatmiser.com/hc/en-us/articles/360018918619), NOT all zones
-
13 Mar, '22
Grodon Graham MergedHours run across all zones should be avilable not just the per zone(which is hidden away in enhanced hisotry), would be nice to see a graph of hours on over time so you can see if consumption is going up or down.
-
03 May, '22
RoyC MergedI don't think this has been 'DONE'. It certainly shows on a 'per zone' basis but I thought the requirement was to have a single graph that showed when the boiler was on (for any/all zones).
1 -
08 May, '22
RoyC Merged"Timer measuring heating being on for each zone and all zones" (suggested by James on 2019-11-08),...." was merged by Heatmiser R&D but this hasn't been completed so the status of this item should not be 'DONE'.
-
11 May, '22
AJM MergedBeing able to measure boiler running time for heating / hot water separately would be great for calculating cost of heating versus h/w etc. Even better if you could put in specs of energy input (boiler / immersion heater etc) so you can even forecast energy costs by your app settings.
-
03 Aug, '22
Heatmiser R&D Admin"Summed Up Boiler "On" time reporting" (suggested by Johny on 2022-02-04), including upvotes (2) and comments (0), was merged into this suggestion.
-
03 Aug, '22
Heatmiser R&D Admin"BOILER RUN FOR THE DAY IN HEATING MODE ONLY ….neo HUB" (suggested by ROY AAC on 2021-11-25), including upvotes (9) and comments (0), was merged into this suggestion.
-
03 Aug, '22
Heatmiser R&D Admin"Boiler burn time reporting/graph on (for each zone and all zones) (neoHub Gen 2)" (suggested by Martin on 2019-10-23), including upvotes (53) and comments (9), was merged into this suggestion.
-
09 Dec, '22
David A100% agree that aggregated boiler run time (daily) is badly needed. That's the figure you need to accurately judge overall run cost. Surely it's pretty trivial to implement for a programmer as all the data is already there?
Looking forward to it as soon as possible. In all other respects the app is now very good (finally). -
04 Jan, '23
Paul WielgutAbsolutely a great idea - to have an overview of how much demand you've had across the whole period (day). To be able to identify how many zones were in use at any given time and the start/end times.
This would help to tune the system for maximum efficiency.
This should also include operation for reasons outside normal programming - failsafe operation etc. -
12 Aug, '24
Thomas Sheppard AdminDone as part of Enhanced history.