Our customers made these suggestions for improving Heatmiser. Suggestions for improving Heatmiser.
We reserve the right to change / cancel or delay any planned feature listed here.
With this in mind, you should NOT purchase a product based on any future feature listed here, including those marked as planned.
Comments asking for release dates will NOT be approved for inclusion here as we don’t promise anything before we can deliver it.
Neo App: Provide greater flexibility on the features guest users are permitted to change
Whilst a guest user is a useful feature, it would be far more flexible to allow the admin user to decide what features a guest is allowed to change, eg via a settings ...
Under consideration
Central multizone programmer and remote sensors
When a multizone heating system has App control, it is no longer necessary to have a programmeable roomstat fitted in each zone, only a temperature sensor - the ...
Not planned
Flame notification in taskbar when heating or hot water on
It would be useful to have an icon appear in the taskbar whenever heating or hot water is active. This would help to tune programmed settings. Particularly useful ...
Not planned
Soft landing pre-heat for when temperature is falling
We have wet underfloor under a 125mm slab/stone finish, our set temp is constant @17.5c 24/7, and the temp differential is 0.5c - so the pump kicks in @17c. We ...
Under consideration
Velux and Heatmiser thermostat integration
I have a number of Velux windows in my apartment which can be controlled by a heat sensor. I have done this in one room only as the sensors are very expensive. ...
Not planned
Failsafe
Currently if there is a power issue to a thermostat it has 2 options in the settings
a) failsafe - heat the zone for 20% of the time
b) no heating
it would be ...
Under consideration
System extended history
Love the new ext history information. My understanding at present is that it reflects each zone. I think it would be helpful to have a graph showing the whole system ...
Not planned
Add ability to change location names in app
At present it is not possible to change the location names in the app, only delete and re-add. Caould this not be easily changed to allow location name editing?
Done
Humidity Sensor
Humidity measurement of the room. Integrate it into neoStat or as a new device like the Air Sensor
Not planned
Lighting control
Add lighting control either through smart hub integration (zigbee hub/ hubitat/ smartthings) or neo dimmer units/ switches (similar to neoPlug).
Not planned
Minimum run time setting
For oil/diesel fuelled boilers/heaters (boats/remote homes) it is important that the boiler runs for at least 30 mins when commanded to avoid the combustion chambers ...
Not planned
Push notifications when heating switches on/off
Would be useful to see when the heating comes on or off on thermostats and to be informed via the app. This could also act as a stop gap until the graph calling for ...
Not planned
Add Profile to each zone on Home screen
It would be useful to see straight away what profile is in use for each zone on the home screen list rather than going in to each individual zone.
Not planned
World clock for any timezone
Currently time synchronization is possible only for 3 timezones. With other, the clock drifts and doesn't keep time. Should be very simple to add support for any ...
Not planned
For ACCESSIBILITY, extend 4 sec (!) illumination on NeoAir v2control panel ... and anything similar!
Our NeoAir v2 is the control centre of our system and the touch screen is illuminated when 'pressed'. But the illumination turns off after 4 seconds in duration - ...
Not planned
Access recipes via Neo Ultra
To be able to access recipes set up on the app and stored on the hub via the Neo Ultra.
We have a set up in a pensioners home which includes a Neo Ultra connected ...
Not planned
Reduced optimiser target temperature
Modification of the optimiser so that it’s target temperature at the time of occupancy can be set lower than the setpoint.
It is generally acceptable for the space ...
Not planned
Neo Switch added to Neo product range
I have a house with 17 Neostat V2 circuits but would like to add wired switches to the system to control lights etc. Obviously a Neostat could be set to timer mode ...
Not planned
Umderfloor Heating water temp control
Hub to control thermostat on underfloor heating manifold. We have underfloor heating in a timber floor. It is really sensitive to outside temperature despite being ...
Not planned
Minimum floor temp setting
When a floor temp sensor is used with an air sensor you can set a maximum floor temp but not a minimum. A minimum temp would mean you can stop the floor cooling too ...
Not planned
APP - Display Zones, Profiles and Recipes in alphabetical order
The order of list item display appears to be based in when each item has been input, making it difficult to find an entry easily.
Please can you enable alphabetical ...
Not planned
Recipes to be stored on neoHub CLOSED FOR NEW COMMENTS
I have asked before and will ask again if recipes can be shared at the hub level. (like profiles) recreating recipes on each of my many mobile devices is a royal ...
Done
New Product Ideas
Ability to copy existing room/zone to a Profile
When a room/zone is created NeoApp currently offers the option to store this as a Profile. If No is selected, you cannot currently go back and copy Room to a Profile ...
Done
Switched output for elec towel rads
Could the 16A switched output module be configured as a zone without thermostat? So it could control either immersion heater or electric towel rads - essentially ...
Done
Hold in IFTTT having the ability to custom times
As above, can we customise the hold times rather than pre configured times. If not possible, can we have 10 and 20 minutes added please
Done
On/Off display in Home Kit
If in Heatmiser Ne app the thermostat is set to "Standby/Away" (with other words heating system off), In HomeKit it show as "On" (with other words Standby/Away is ...
Under consideration
Heatmiser Mobile App temp alerts
When using the heatmiser small battery remotes. Most are not paired to any thermostat and simply provide a good way to visually check the temperate in various rooms, ...
Under consideration
Failsafe notification
Failsafe can indicate an issue with communication with wireless thermostats and heating can occur without householders knowing for extended periods of time.
Please ...
Not planned
Additional custom modes such as 'Working from Home'
In addition to holiday/away modes, be able to add custom modes such as "Working from home" or "Kids off school" where a custom set of heating profiles/schedules can ...
Done
Bring back the Bar Chart in the expanded history
Really useful to have broad weekly overview of usage. Where has it gone?!
Not planned
Support average temperature between built-in and remote sensor(s)
An average temperature can be used to control a zone from multiple wireless sensors but this doesn't allow the built in sensor to be included. My suggestion is useful ...
Done
Ability to Lock profile so that it can’t be messed with. CLOSED FOR NEW COMMENTS
Ability to Lock profile so that it can’t be messed with.
Done
Add graph line to “Enhanced History” for external temperature
The current “Enhanced History” information is excellent and it was great to see you add the external temperature information to it, however it could be made ...
Under consideration
Have More Heating/ Timer ON/ OFF Cycles
Allow the app to give hot water and importantly heating timers more on/ off cycles. Currently max is 6 heating levels, but would be useful to have more.
Can the ...
Under consideration
Marking the difference!
We found out by accident that our electric underfloor heating had been installed with regular neoStat controllers, rather than correct neoStat-e controllers.
Our ...
Not planned
Development/ support for smart bulbs linked to Neo hub
Ability to control a smart bulb through the Neo hub .. in the same way as the current smart plugs would be a welcome enhancement
Not planned
Add a minimum and maximum temperature limit
The current Neo system offers limits of up to +/- 5C which apply to the current comfort level. This appears to be defeatable by setting a HOLD temperature. I would ...
Under consideration
Locking a Neo Hub
I have just lost access to my home Neo hub remotely - someone in the house downloaded the App -registered for an new account then pressed the reset button on the hub ...
Not planned
Humidity readings to control fans etc
I think that there should be a unit that has the ability to read humidity to control fans, it can be based on a timer so that times can be added to bathrooms/ ...
Under consideration
Access to the webservice used by the app using api key
Access to the webservice used by the app using an api key similar to how the twitter api works.
Not planned
Homekit-capable hard-wired switch - ideally two-way and intermediate.
It would open up so many possibilities to have a switch which could be hard-wired into circuits to give Homekit control, rather than just a plug-in one.
If it ...
Under consideration
Plugged in electrical thermostat
Please try to manufacture a new electrical thermostat that can be plugged in to already existing electrical socket. This way we avoid the cost of batteries and the ...
Not planned
Target temperature bands for time of use electrical tariffs when using domestic Heat Pumps
Target temperature bands will allow the system to heat to the maximum target temperature when electrical tariffs are cheap and when electrical tariffs are high only ...
Not planned
Access to more detailed information for installers
The hub API provides far more information than is present in the standard user app, for both thermostats/devices and the hub. Could a "pro/installer" mode be ...
Not planned
Calibration of sensor from the app
Suggestion for a future release is to be able to calibrate the temp sensor from the app. Currently this is done from the keypad, but when it’s at the back of a ...
Not planned
iPhone App Update
On my Apple iPhone app, when a room thermostat is requesting the boiler to fire up, I see a flame symbol to the right of the zone that is heating. I do not see that ...
Not planned
Standby returning to it last setting
When standby returns to non standby mode it returns to the programmed time/temperature settings rather than its last setting which may be an overiden temperature. ...
Not planned