Suggestions for improving Heatmiser.

We reserve the right to change / cancel or delay any planned feature listed here.

With this in mind, you should NOT purchase a product based on any future feature listed here, including those marked as planned.

Comments asking for release dates will NOT be approved for inclusion here as we don’t promise anything before we can deliver it.

Heating On/Off Indication on History graph (Gen 2 neoHub)

On the temperature history graphs (including expanded history), it would be really useful to show when the heating was turned on and off. Being able to determine ...
Suggested by: Customer Feedback (23 Aug, '19) Upvoted: 20 Feb Comments: 40
Done neoApp

Neo Smartthings Integration

Integrate with Smartthings
Suggested by: Customer Feedback (23 Aug, '19) Upvoted: 21 Sept Comments: 10
Not planned New Product Ideas

Weather compensation

Some form of weather compensation - either via an external sensor - or via internet weather would be great. The time taken to increase temperature in my house by 1 ...
Suggested by: Jonathan (11 Nov, '19) Upvoted: 11 Sept Comments: 21
Under consideration

To be able to export the history data of all stats for external analysis

The current history information being for a week would be useful if exportable to build up a long term picture. Helping with understanding how the system behaves and ...
Suggested by: Malcolm (28 Oct, '19) Upvoted: 20 Sept Comments: 22

App should connect directly to the hub when on same network to improve laggy user experience

There is network lag when using the app. It should be able to detect if it is on the same network as the hub and communicate with it directly. I've setup my own ...
Suggested by: Jit (04 Oct, '19) Upvoted: 06 Nov, '22 Comments: 9

Aggregated graph for all zones.

Related to which suggests it is possible to see the aggregated total ...
Suggested by: Paul (07 Mar, '22) Upvoted: 04 Jul Comments: 14

Graphs that can Zoom and Auto Scale

History chart should have a more zoomed in y axis - currently my temperatures are all somewhere between 20 and 25 degrees but impossible to accurately read. It could ...
Suggested by: Customer Feedback (23 Aug, '19) Upvoted: 13 Jul, '22 Comments: 3
Done neoApp

0.5 Set Temp on (Gen 2 neoHub) - CLOSED FOR NEW COMMENTS

To be able to set the temp 0.5 increases rather than the 1 , we have currently
Suggested by: Customer Feedback (23 Aug, '19) Upvoted: 24 Feb Comments: 6

Longer history

History to show 1 month
Suggested by: Martin (23 Oct, '19) Upvoted: 29 Jan, '21 Comments: 8

Hot Water Control with External Sensor

How about making any of your stats do hot water control using the external sensor as a cylinder probe? This would avoid the additional expense of buying and wiring ...
Suggested by: John (23 Aug, '19) Upvoted: 12 Aug Comments: 13
Not planned New Product Ideas

linked heat demands

Please add in clever control. If one zone has called for heat as its reached its threshold, the other zones should also be able to be switched on if below target ...
Suggested by: Pete (07 Nov, '19) Upvoted: 08 May Comments: 6
Not planned

See floor temperature in app

It would be good if you could see the floor temperature in the app. On both the summary page (showing all rooms) and the individual room details.
Suggested by: Nige (27 Oct, '20) Upvoted: 28 Apr Comments: 3

Ability to copy a profile as a starting point for a new profile

For my multi zone system I have a Winter profile and a Summer profile for each zone. For mild periods during the winter, the Winter profile gives too much heat. I ...
Suggested by: Grahame Crispin (13 Dec, '19) Upvoted: 28 Dec, '22 Comments: 2

Add support for Matter

Matter is a connectivity standard backed by Amazon, Apple, Google, and many other technology companies. See:
Suggested by: Alessandro Rossini (14 Sept, '22) Upvoted: 21 Sept Comments: 1
Under consideration

UFH Pump Delay ON / OFF

Just commissioned my UFH-8 controller and the pump starts straight away when called for by my NeoUltra ie before the thermal actuator (TA230) are opened, so the pump ...
Suggested by: Steve (17 Nov, '19) Upvoted: 25 May Comments: 3
Not planned


Why not produce a more expensive model of your wireless room thermostat , which includes a symbol showing humidity as well as temperature?
Suggested by: D McCallum (06 Mar, '20) Upvoted: 07 Sept Comments: 2
Under consideration

0.1 0.2 etc degree options for differential

For underfloor heating 0.5 degree differential is still too large. The floor temp takes too long to respond when allowed to cool so much
Suggested by: Rob (09 Nov, '19) Upvoted: 07 Sept Comments: 5
Not planned

Multiple Settings backup and restore

I have a Neo system consisting of 10 devices - room and underfloor thermostats and timers for boiler and towel rails. As the seasons progress many settings have to be ...
Suggested by: Tim (03 Oct, '19) Upvoted: 30 Apr Comments: 8
Not planned

Colour status icons in neoApp

In the neoApp, make the colour of the circular room status icons and the temperature in these change automatically so that when: - Heating -> Red icon, ...
Suggested by: Customer Feedback (16 May, '20) Upvoted: 13 Mar, '22 Comments: 0
Not planned

Opentherm compatability with wired thermostats

The neo air has an open therm controller, why not the rest of the product line?
Suggested by: Harry (16 Feb, '20) Upvoted: 10 Jul Comments: 3
Under consideration

Push Notifications on Neo App. CLOSED FOR NEW COMMENTS

Can you make your heatmiser app trigger an alert message on my phone when the battery is low on a thermostat? This would be invaluable so the thermostat would not go ...
Suggested by: Samir Mabruk (23 Aug, '19) Upvoted: 13 Sept Comments: 7
Done neoApp

Grid display and floorplan display option in neoApp

Add an option in the neoApp to display the room status in a single-page grid (a tile for each room, including target temp, current temp, flame and snowflake status ...
Suggested by: Customer feedback (12 May, '20) Upvoted: 03 Jan, '21 Comments: 5

Include battery % status in HomeKit app similar to how Philips hue battery sensors display battery %

Include battery % status in HomeKit app similar to how Philips hue battery sensors display battery % in the status details section
Suggested by: Noel Burke (17 Oct, '19) Upvoted: 02 Mar Comments: 1
Not planned

Record + display external sensor temperatures in app

It's great that the app records the temperature history of the internal sensor. It'd be even better if it also recorded the history of the attached floor-probe. ...
Suggested by: Marcus (08 Apr, '20) Upvoted: 06 Jan Comments: 2
Under consideration

Compensate for zone 'overshoot' by shutting off thermostat output early

With radiators in the loft rooms, the temperature overshoots the 'set' value because the Neostats shut of at the set point while the radiator continues to heat the ...
Suggested by: Mike (28 Jan, '21) Upvoted: 12 Aug Comments: 0
Under consideration

Enhanced wireless air sensor app integration

- when a neoStat is linked to one or more wireless air sensors, show in the app the temperature of the wall thermostat as well the air sensor(s) and the average. At ...
Suggested by: JB (22 Sept, '21) Upvoted: 11 Sept Comments: 1
Under consideration

Hold from standby mode.

Make the hold function operate from standby and return to standby afterwards.
Suggested by: David (19 Sept, '19) Upvoted: 27 Jun, '21 Comments: 1

Higher Away Temperature - Heat pump

Increase away temp range to at least 20C. Ground source heat pumps need to be st least 19-20DegC on tick over in winter when away.
Suggested by: Customer Feedback (23 Aug, '19) Upvoted: 07 Feb, '22 Comments: 5
Not planned neoApp

Set whether failsafe turns heating on or off

At the moment if a zone neostat runs out of battery the heating comes on permanently. Useful for the winter - a disaster for the summer. Allow your customers ...
Suggested by: Daniel (23 May, '20) Upvoted: 13 Sept Comments: 2
Not planned

MacOS app or website control

Could Heatmiser develop the ability for Mac OSX (not iOS) users to control the neohub/neosystem via a macOS app or website address? Enabling this will offer Mac OS ...
Suggested by: Mark (05 Nov, '19) Upvoted: 13 Sept Comments: 0
Not planned

Outside Thermo to connect to hub

Or just local weather station temp to show on home screen
Suggested by: Martin (23 Oct, '19) Upvoted: 06 May, '22 Comments: 4
Not planned

Wired Air Sensor

To get over the disadvantages of the current wireless air sensor which only reads every 5 minutes and to 0.5 degree accuracy and will not join the MESH. Could a Air ...
Suggested by: Pierre Hymas (01 Mar, '21) Upvoted: 30 Jan Comments: 2

Show remote air sensor battery levels in App

Display remote air sensor battery levels in App.
Suggested by: Gregg Kennedy (16 Feb, '20) Upvoted: 06 Jan Comments: 2
Not planned

Live temperature feed for IFTTT

To add a live temperature feed available on IFTTT from hub-connected stats. This could work with various "actions", such as integration with smart heat pump control.
Suggested by: Phil (19 Nov, '19) Upvoted: 31 Jan Comments: 1
Not planned

Open source your firmware so that the community can contribute

Consider open sourcing your firmware / software so that the open source development community can contribute. I applaud you on the fact that you have a telnet API ...
Suggested by: Jit (08 Dec, '19) Upvoted: 02 Jan Comments: 0
Not planned

MAC Address on the Neo Hub to all MAC Binding

By adding the printed MAC Address on the Neo Hub it will save time for MAC binding on the FIXED IP
Suggested by: The Integrator (22 Nov, '19) Upvoted: 10 Jul, '22 Comments: 0
Not planned

Heatmiser App to allow Week Day/ Week End changes

Can the Heatmiser Neo app please be updated to allow different on/ off cycles to be possible for heating and hot water based on day of week, or at least one setting ...
Suggested by: Steve (19 Nov, '20) Upvoted: 04 Nov, '22 Comments: 4

Advance scheduling of ‘Away/Holiday Planning’

I have a neo hub gen 2 and would like to be able to plan in advance away/holiday schedule. This would save me setting away date/time only when I leave the house
Suggested by: Paul Amos (05 Dec, '19) Upvoted: 13 Jul, '22 Comments: 2
Not planned

Zigbee channel selection

Allow the customer to select the Zigbee channel using the settings in the App as opposed to having to contact Heatmiser support who apparently can change this.
Suggested by: Marko (29 Jan, '21) Upvoted: 12 Jun Comments: 0
Under consideration

More Date Information Please On Landing Page

For those of us who are dealing with irregular zone programming, it would be most useful to add the day of week the next heating change is due to take place. 'Next ...
Suggested by: Simon Brown (17 Nov, '19) Upvoted: 08 Nov, '22 Comments: 0
Under consideration

IFTTT Action to run Recipe on neoHub

Allow recipes to be triggered now that they are stored on the hub.
Suggested by: Dion Stuart (23 Aug, '19) Upvoted: 08 Mar, '21 Comments: 4

larger and/or more readable font colour

The orange on white is really hard to see at times. a darker font colour would help
Suggested by: Karl (10 Dec, '19) Upvoted: 13 Nov, '22 Comments: 1
Under consideration

Add IFTTT trigger for when NeoStat is calling for heat.

Similar to the idea to add heating on/off to the app, it would be great if you could also add a trigger event to IFTTT for when the NeoStat calls for heat, and when ...
Suggested by: Steve (23 Oct, '19) Upvoted: 13 Apr Comments: 2
Not planned

NeoStat v2 to communicate with UFH-8 RF

It would be useful if the NeoStat v2 could communicate with the UFH-8 RF wiring centre. This would probably be a useful feature for any system that has a mix of ...
Suggested by: Phil (19 Nov, '19) Upvoted: 06 Jul Comments: 1
Not planned

HomeKit Support for Window / Door Sensor

I would like to see the door/window sensor shown as a HomeKit device, to allow me to use the units in other automations within the iOS Home app. Presenting all ...
Suggested by: 404_ERROR (02 Jan, '21) Upvoted: 03 Apr Comments: 1
Not planned

Air conditioning control or intergration

Control of air conditioning, or at least an ability to turn off heating when cooling is activated.
Suggested by: Harry (16 Feb, '20) Upvoted: 25 Apr Comments: 1
Not planned

Lifting the 35ºC limit

Can we please lift the 35ºC max limit in the app, we can set higher on the keypad but the app will reset it if you enter. Very frustrating.
Suggested by: Darren Yearsley (15 Feb, '21) Upvoted: 20 Aug Comments: 1
Not planned

Add MQTT messaging on neo-hub to make integration to third party products quicker and easier

MQTT - Message Queue Telemetry Transport (see is the defacto standard for IOT communication. It works on a simple pub-sub model and the neohub could ...
Suggested by: Philip Gilbert (29 Oct, '20) Upvoted: 16 Jan Comments: 1
Not planned

Opentherm Gateway to support Multiple Zones

The lunch of the Neo Hub Mini is great news for supporting OpenTherm for small properties. Could we please have support for Multiple zones as the vast majority of ...
Suggested by: Ashok (10 Jul, '20) Upvoted: 28 Jan Comments: 1
Not planned

More One/ off Cycles & Levels

Can the Heatmiser Neo app please be updated to allow more on/ off groups to be possible. This would be very useful for heating, and also for example for timers. We ...
Suggested by: Steve (19 Nov, '20) Upvoted: 05 Jan Comments: 0
Not planned